This is an adjustable double leg, shock absorbing lanyard with two Scaffolding hooks and a single screw gate carabineer that is engineered to attach to a dorsal D-Ring on a stand-alone, fall arrest harness.

This lanyard is recommended for those who are required to navigate obstacles whilst working at heights. The double leg lanyard improves

safety to the wearer by allowing the wearer to remain attached to at least one anchor point at all times through the use of one hook, while moving the second hook around the obstacle to a new anchor point.

The adjustable legs allow the wearer to reduce the overall length of the lanyard, thereby reducing the fall distance and following best working-at-heights practice.  The built-in shock absorber is engineered to reduce the total force experienced in a fall to a survivable force of less than 6kN.

• Adjustable double leg with scaffolding hooks
• Single leg with screw gate carabineer
• Shock absorber

This is an elasticated double leg, shock absorbing lanyard with two Scaffolding hooks and a single Snap hook connector that is engineered to attach to a dorsal D-Ring on a stand-alone, fall arrest harness.

The elasticated lanyard lifts the hooks off the ground when not in use, reducing the wear and tear caused to hardware when dragged on the ground. It further improves safety to the wearer by reducing the potential of the lanyard being caught in dangerous machinery.

This lanyard is recommended for those who are required to navigate obstacles whilst working at heights. The double leg lanyard improves safety to the wearer by allowing them to remain attached to at least one anchor point at all times, through the use of one hook, while moving the second hook around the obstacle to a new anchor point.

The built-in shock absorber is engineered to reduce the total force experienced in a fall to a survivable force of less than 6kN.

• Elasticated double leg with scaffolding hooks
• Single leg with snap hook
• Shock absorber

Material: Plastic

Set of 2

Colour: red

• Measures AC/DC voltage & current, resistance, capacitance and frequency

• Tests diode, triode, battery and continuity

• Overload and short circuit protection

• Non-contact voltage detection with wire or cable identification diode test (high, medium, low indication)

• Display: 6000 Counts

• DC voltage: 1000V

• AC voltage: 750VDC

• AC/DC Current: 10A

• Resistance: 60MΩ

• Capacitance: 100MF

• Duty cycle: 5~95%

• Frequency: 10MHZ

• Low battery indication

• Backlight

• Data hold

• Auto power off

• Checks 12 volt battery and alternator systems
• LED light for easy and accurate reading

• Tests for voltage and circuit integrity on 3 - 48 volt systems

• Ideal for use on most vehicles including cars, motorcycles, RVs, trailers, boats and trucks

• Computer safe

• Digital LCD display for precise voltage reading

• Long, stainless steel probe for testing in confined areas and piercing through insulation

• Ground clip with insulated sheath

• 3.6m Heavy-duty coiled cord for flexibility and reach

62piece 3/8″ Dr. Tool Set

Content:

- 15x 3/8″ Dr. 6pt Sockets: 7, 8, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 21, 22, 24mm

- 1x 3/8″ Dr. Quick-Release Offset Ratchet

- 1x 3/8″ Dr. Universal Joint

- 2x 3/8″ Dr. Spark Plug Sockets: 16, 21mm

- 2x 3/8″ Dr. Extension Bars: 3″(75mm), 6″ (150mm)

- 10x Combination Wrenches: 8, 10, 11, 12, 13, 14, 15, 17, 18, 19mm

- 1x 1/4″ Dr. Spinner Handle

- 1x Bit Coupler – 1/4″ Dr. x 1/4″

- 24x 1/4″ Screwdriver Bits (25mm):

       4x Phillips” #0, #1, #2, #3

       4x Slotted: 4, 4.5, 5.5, 6mm

       7x Star: T10, T15, T20, T25, T27, T30, T40

       5x Hex: 3, 4, 5, 6, 7mm

       4x Pozi: #0, #1, #2, #3

- 2x Screwdrivers: Phillips #2 x 100mm, Slotted 6.5mm x 100mm

- 1x 6″ (150mm) Diagonal Cutting Pliers

- 1x 7″ (180mm) Combination Pliers

- 1x 7″ (180mm) Locking Grip Pliers

- Blowcase

• Heavy duty construction

• Retractable blades for safe storage

• Four adjustable cutting positions

• Extra blade included